Home | Site Map | Cisco How ToNet How To | Wireless |Search | Forums | Services | Donations | Careers | About Us | Contact Us|

Setup Cisco WLC 2504 Using Startup Wizard

Cisco Router, Firewall, VPN, SDM, ASA and Switch

Setup Cisco WLC 2504 Using Startup Wizard

Postby guest » Wed Jun 06, 2012 11:55 am


31535298 bytes read
Launching images...
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 672, tty '': '/etc/init.d/rcS'

type = block
dump-device = 254:4
level = header
compress = none
ifconfig: SIOCGIFFLAGS: No such device
Detecting Hardware ...
Installing ether-pow driver - 0x6008
starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'

Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
octeon_device_init: found 1 DPs
/dev/fpga: No such device or address
readCPUConfigData: cardid 0x6060001
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.

Cisco AireOS Version
Firmware Version PIC 16.0

Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU00: Initializing last packet received queue. Num of cores(2)
Fastpath CPU00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU00: Core 0 Initialization: ok
Fastpath CPU01: Core 1 Initialization: ok
Fastpath CPU00: Initializing Timer...
Fastpath CPU00: Initializing Timer...done.
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Licensing Services: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting RRC Services: ok
Starting FMC HS: ok
Starting Management Services:
Web Server: ok
CLI: ok
Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
License Agent: ok

(Cisco Controller)

Welcome to the Cisco Wizard Configuration Tool
Use the '-' character to backup

Would you like to terminate autoinstall? [yes]:
AUTO-INSTALL: starting now...
rc = 0


System Name [Cisco_e2:6d:84] (31 characters max): WLC2504
Enter Administrative User Name (24 characters max): is
Enter Administrative Password (3 to 24 characters): ********
Re-enter Administrative Password : ********

Management Interface IP Address:
Management Interface Netmask:
Management Interface Default Router:
Management Interface VLAN Identifier (0 = untagged): 0
Management Interface Port Num [1 to 4]: 1
Management Interface DHCP Server IP Address:

Virtual Gateway IP Address:

Mobility/RF Group Name: RF

Network Name (SSID): WIFI

Configure DHCP Bridging Mode [yes][NO]: NO

Allow Static IP Addresses [YES][no]: YES

Configure a RADIUS Server now? [YES][no]: YES
Enter the RADIUS Server's Address:
Enter the RADIUS Server's Port [1812]: 1812
Enter the RADIUS Server's Secret: *********

Enter Country Code list (enter 'help' for a list of countries) [US]: US

Enable 802.11b Network [YES][no]: YES
Enable 802.11a Network [YES][no]: yes
Enable 802.11g Network [YES][no]: yes
Enable Auto-RF [YES][no]: yes

Configure a NTP server now? [YES][no]: yes
Enter the NTP server's IP address:
Enter a polling interval between 3600 and 604800 secs: 36000

Configuration correct? If yes, system will save it and reset. [yes][NO]: yes
Tablet and Smartphone Setup Guide

Troubleshooting Vista Wireless
Posts: 10191
Joined: Mon Nov 27, 2006 1:10 pm

Return to Cisco

Your Ad Here

Who is online

Users browsing this forum: No registered users and 3 guests